How My Custom Electric Guitar Was Built, Step by Step

Watch How My Custom Electric Guitar Was Built, Step by Step on YouTube

Watch the video on YouTube

If you watched my cover of Sultans of Swing with my friend Josh Turner, you might have noticed my custom Fiesta Red guitar. It was made by Marceau Guitars, founded by Tom Marceau in 2008. He and his small team of luthiers have built hundreds of custom guitars in their workshop in a small commune in Brittany, France. They are the same makers behind my Heartbreaker guitar.

Tom and the team kindly filmed the whole process, so if you've ever wondered how a guitar is made, this is how it's done. The YouTube video is a shortened version; there's an extended two-hour cut on Nebula.

1. The body

Once the wood has been selected, it's cut on a circular saw and sent through the planer. This body is alder, in two pieces, which are glued, clamped and planed again. A stencil lines the wood up precisely, then the body shape is machine-cut and the cavities for the pickups, electronics and bridge are milled out.

2. The neck

The neck follows a similar process, here in flamed maple: cut, planed and machine-cut, with the channel for the truss rod milled out. The fingerboard is cut on the bandsaw and planed. Using computer-aided design, the signature inlay that sits at the 12th fret is lined up and checked, and the machine runs a simulation before it mills the fret slots, truss rod cover, dot inlays and signature inlay.

3. The fingerboard

Magnets for the truss rod cover are hammered in by hand, and the cover is cut and fitted. Side dots are marked, milled, glued in and trimmed. To avoid vibration, the truss rod gets a heat-shrunk sheath before it's hammered into the neck. The fingerboard is then glued, pinned and clamped, and once it's dry the whole neck is shaped by the milling machine.

4. Finishing the body

The body is hand-sanded and drilled for the wiring and strap buttons. A clear coat goes on and is sanded back, then a white base coat, then the Fiesta Red nitrocellulose lacquer. Once dry, it's lightly wet-sanded, and shielding is cut and fitted into the control and pickup cavities.

5. Finishing the neck

Resin is applied by hand to the fingerboard inlays, which are then pressed in. The fingerboard radius is measured, checked and lightly sanded, and the fret wire is pressed into place, clipped and sanded flush. After more shaping, the frets are masked off and the first coat of lacquer goes on. The logo decal goes on the front of the headstock and "Made in France" on the back, before the neck gets a vintage-tint lacquer.

6. Pickguard and pickups

The mint green pickguard is machine-cut, bevelled and finished by hand, with shielding on the back, and the pots and switch are wired up. Then the single-coil pickups are made: slugs are fitted and glued, the pole pieces magnetised, and each pickup is wound by hand. Finally they're wax-potted, soaked in wax so the components can't move, which makes them quieter and more reliable.

7. Fret finishing

The luthiers check the neck and body for any final adjustments. Then the fret ends are rolled and buffed by hand to remove sharp edges and give the neck a played-in feel.

8. Relicing

This is my favourite part. The body is sandblasted, then the lacquer is frozen and tapped with a screwdriver. Nitrocellulose is very sensitive to temperature changes, so this causes fine cracks, called checking, like you see on old nitro guitars from the 1950s and 60s. A buffing wheel removes finish where a guitar naturally wears, and chips and dings are added by hand to suggest twenty years of gigging. The neck and fingerboard get the same worn-in treatment.

Shiny new hardware would look out of place, so it's aged in a corrosive bath. The knobs are scratched with a scalpel, even rubbing off some of the lettering.

9. Assembly

The tuners go on, guide holes are drilled for the pickguard, and the bridge, tremolo block and springs are fitted. The wired pickguard goes in, the jack socket is soldered and grounded, and the pickups are tested before everything is screwed together.

10. Nut and final set-up

After some bridge adjustments, a piece of bone is fitted into the nut slot, then cut, shaped and slotted for the strings. The strings and string trees go on, the action is set, and a final tweak to the pickup height gets it just right.

If you're fascinated by how guitars are made, you'll also enjoy my articles on how the Fender Stratocaster is made and the PLEK machine.

Previous
Previous

How to Feel Less Intimidated in a Guitar Shop

Next
Next

My First Fender Telecaster, and the Story of the Tele